Plumbing and heating specialists, Littleborough

Central heating power flush in Littleborough

Radiators that stay cold at the bottom, or only warm up in patches, usually mean sludge has settled in your central heating system.

Gas Safe registered 504382. 24/7 emergency and same-day call-outs.

4.9 from 134 Google reviews

Ask for a free quote

Paul rings you back to talk it through.

We only use your details to reply. Privacy

“Paul came out to our boiler within an hour of calling…”
Josh M
“Absolutely lovely team, father and son, professional, polite, tidy.”
Kelly D
“Save his number Great Plumbers are hard to find and Paul is one of them.”
Jason C

A power flush clears it out. Paul Hanna will tell you honestly whether yours needs one before he quotes for it. Ring 07966 200813.

A power flushing machine connected up with hoses outside a house
Paul's power flushing machine, connected up.

Ask for a free quote

Paul rings you back to talk it through.

We only use your details to reply. Privacy

What a power flush is

Over the years, the water in your central heating system picks up rust and bits of debris from the metal it runs through, and sometimes limescale. It turns into a black sludge that sinks to the bottom of the radiators and collects in the boiler. Water can't get past it, so you get cold spots, higher heating bills and parts that wear out early.

A power flush pushes water round the radiators and pipework at speed with a cleaning chemical in it. The chemical loosens the sludge and debris, and the flow carries it out, so the radiators heat up properly again. It's the most thorough way to remove sludge without taking every radiator off the wall.

Will fitting a wall-hung toilet beside a black towel rail in a grey tiled bathroom
Will fitting a wall-hung toilet.

Signs you need a power flush

You might need a power flush if:

  • Your radiators have cold spots, usually along the bottom
  • Some radiators never get hot, even with the heating on full
  • The water is black or brown when you bleed radiators
  • You're bleeding them often and they still don't heat up
  • Radiator valves have seized or are hard to turn
  • The boiler is noisy, or keeps cutting out with no fault anyone can find
  • You're having a new boiler fitted on an older central heating system

Not every cold radiator needs a flush. Air, a stuck valve or a pump that's failing can all look the same from the sofa, so we check your system before we recommend anything. If a cheaper repair will sort it, that's what we'll suggest.

An older boiler in a cupboard with its front casing removed, showing the burner and controls
An older boiler opened up.

How we power flush a system

Here's what happens on the day:

  1. A power flushing machine goes on the system, with a magnetic filter on it to catch the rust and dirt as it comes out.
  2. A cleaning chemical goes in to break the sludge down.
  3. We work through the house one radiator at a time, sending the flow through each one in turn while fresh water goes in.
  4. The flushing carries on until the water coming out runs clean.
  5. The system is refilled and a corrosion inhibitor goes in, which protects the metal from rust building up again.
  6. We run the heating and check every radiator heats up from top to bottom.

If your boiler hasn't got a magnetic filter on it, we fit those too, so ask about one when we quote.

Copper pipework run neatly down the wall under a newly fitted boiler
Pipework under a new boiler, run straight and clipped.

Why it's worth doing

Clean heating systems warm the house faster, and the boiler doesn't have to work as hard to do it. Getting the muck out also takes the strain off the pump and the heat exchanger, so the whole system lasts longer and the boiler's less likely to break down.

When Paul fixed a boiler that kept cutting out for Dave H, he flushed the system too: "unbelievable how much 'gunck' was in the pipes and radiators!"

Heating gone off altogether? Our boiler repair page is the place to start.

An old floor-standing boiler with its casing off, in a kitchen corner, before being taken out
An old floor-standing boiler, on its way out.

Power flushing before a new boiler

Putting a new boiler on a dirty system is asking for trouble, because the sludge that blocked the old one goes straight into the replacement. Boiler manufacturers generally expect a system flush when one is fitted, so ask about it when we quote for your boiler installation. Boiler swaps start from £1,599.

A new Baxi combi boiler on a brick wall, with its flue going up and the pipework run neatly below
A new Baxi combi, fitted and running.

Radiators and other central heating work

Paul and his son Will also:

  • Fit new radiators and replace old ones, including traditional cast iron column radiators and towel radiators
  • Rehang radiators that need more support on the wall
  • Replace motorised valves and other faulty parts
  • Fit smart controls such as Hive thermostats
  • Change complete central heating systems
  • Install and repair underfloor heating

Sonia B had radiators "not working properly, though hot water ok" for a couple of years. Paul traced it to a faulty motorised valve: "Came back today with son Will fitted Hive and valve, heating worked straight away."

Samantha P: "Amazing job installing cast iron radiators in both our daughter's room. Quick and efficient and reasonably priced."

Katharine C needed her elderly father's heating sorted before she left: "Paul visited us that afternoon, he explained clearly to me what the problem was and what he needed to do to solve it."

A new white column radiator under a window, against a dark blue wall
A column radiator, swapped in for a standard panel.

Power flush questions

What does a power flush cost?

Ring us for a price. The cost of a power flush depends mostly on the number of radiators and how much sludge is in the system. We'll look at it and give you a free quote before we start.

How long does a power flush take?

We'll tell you how long when we quote. The more radiators and the more sludge, the longer it takes, because every radiator is flushed on its own.

Can a power flush cause leaks?

It doesn't damage sound pipework. On an old heating system, though, sludge can sometimes be the only thing sealing a weak joint or a radiator that's rusting through, and a flush can show that up. If that happens, we'll fix it or tell you what needs replacing.

How often should a system be power flushed?

Only when it needs it. A system that's been flushed, treated with inhibitor and has a magnetic filter can go years without another one. Regular boiler servicing helps spot the signs early.

Can I power flush the system myself?

You can buy cleaning chemicals, but a power flush needs proper kit and a heating engineer who knows the system. Leave anything on the gas boiler itself to a Gas Safe registered engineer. We're Gas Safe registered, number 504382.

Is a power flush the same as a chemical flush?

No. A chemical flush adds a cleaner to the water, runs it round with your heating's own pump, then drains it out. A power flush uses a separate machine to push the water through much harder, one radiator at a time, so it shifts sludge the gentler method leaves behind.

Book a power flush

Ring Paul on 07966 200813 and tell him what your radiators are doing. Or send the quote form and he'll call you back. We cover Littleborough, Rochdale, Todmorden, Hebden Bridge, Halifax, Burnley and the towns around them. Read what other customers say on our reviews page.

Paul and Will standing between the two Hanna Heating vans outside a stone house in LittleboroughPaul and Will

Who comes to your house

Paul answers the phone and does the survey. Will works alongside him, and does the smaller plumbing jobs himself. Between them they have over 40 years' combined experience.

Most of our work comes by word of mouth and from customers we've worked for before.

Paul and Will in their Gas Safe T-shirts, with a bathroom stripped back to the lath behind them

Paul and Will, mid rip-out on a bathroom job

About Paul and Will